Ford 9 In. 3rd Member Assembly 31 Spline STD Spool 5.83 Gear Ratio

Description

These Ford 9″ rear ends are hand-assembled by trained experts in-house, Has a nodular iron housing that is stronger than OEM “gray” iron and has 4 lbs. of additional reinforcement, Use of a large bearing “Daytona” style pinion bearing supports for strength and reliability, A spacer and shim setup maintains critical pinion depth settings and easier to service than traditional crush sleeves, The gear units are built of long-wearing 8620 cold-rolled steel, lightened gear options available
Ford 9 In. 3rd Member Assembly 31 Spline STD Spool 5.83 Gear Ratio
Sku # 91048343-583-STD
Mfr. Part # 91048343-583-STD
Condition
New
Brand
Speedway Motors
Sold
Box
Details
Notes
NOTE: Circle track racing applications require a minimum of 4 qts. of rearend lube. Using less than this amount will lead to immediate pinion failure.
Info
Assembled by Professionals
Hand-assembled by trained experts in-house, our Ford 9-inch third members are built from quality components with an exact step-by-step process. We bring this combination of precision assembly and quality components to you at a price that can’t be beat. We trust these third members so much, they’re the go-to choice for our own rides, from the street to the track.
Tough, Nodular Iron Center Section
Our Ford 9 Inch Nodular Iron Third Member Center Section Carrier starts with a NEW casting with over 4 lbs. of additional material in critical areas. Nodular (ductile) iron is much more resistant to fracturing than OEM “gray” iron. Extra ribbing reinforces the case and rearmost pinion support (pilot bearing).
Thick, forged steel bearing caps surround the carrier bearings, all securely held in place with precision Grade 8 cap screws. The improvements continue with rugged billet steel adjuster nuts and heavy-duty keepers to ensure your ring gear settings are maintained. All mounting surfaces are precision machined to ensure a consistent, flat surface for a positive gasket seal (no more leaks on your shop floor). An oil fill plug is included.
Precision Assembled For Proper Ring Gear Teeth Pattern
Getting a proper pattern on the ring gear teeth is crucial. Our time-proven, step-by-step process ensures the correct backlash, preload, and proper amount of pinion shims to ensure the correct pattern on the ring gear teeth.
To ensure a proper gear pattern, we use a stronger “Daytona” style pinion bearing support to maintain that critical pinion depth setting. Stronger due to its larger bearings, our Daytona pinion support also uses the spacer-and-shim setup to maintain critical pinion depth settings under high load, unlike traditional crush sleeves which often compress further, take out your preload and lead to failure. With solid bearing spacers and the proper shims, we eliminate this problem and make setting preload easy and repeatable during installation, service and gear changes. Since preload is already set, simply torque the pinion nut to 160 ft./lbs. and you’re good to go. The pinion gear is connected to our new, forged steel “Ford short”, 1310-type pinion yoke.
Gear units are built from long wearing, tough 8620 cold-rolled steel.
We offer lightened gear assemblies from 5.29:1 to 6.50:1, select the “L” option (example: 529L) from the gear ratio selection.
Variety of Spool Options
A variety of spools are available, in gearing from 3.50:1 to 7.33:1. Our CNC machined full spools are stronger than mini spools and available in standard, lite and mega-lite configurations:
Standard (STD) full spools are CNC-machined and built for the strip and high-horsepower/torque applications when the ultimate in durability to handle high-traction power is needed. Weight 8 lbs.
Mega-lite (MEGA) full spools are great for lower traction applications such as dirt racing, lowering your rotating weight, reducing your time to peak RPM and reducing unsprung mass. At just 5.49 lbs., these spools are nearly as light as aluminum but have the strength of machined steel
Lite (LITE) full spools are a good combination of weight reduction and CNC-machined steel durability, and weigh only 6.1 lbs.
Proven Reliability
We race what we sell. Our third member units are the go-to choice for our own rides and racecars and we have built these units to last with high quality hardware and components. Tapered steel roller bearings minimize friction, better handle thrust loads and increase load carrying capacity. The ring gears are assembled with Grade 9 bolts with a tensile strength of 180,000 psi, a 15% increase over Grade 8 hardware. Heavy duty Grade 8 carrier cap bolts, a lock-style pinion nut with pre-applied Loctite and high-quality grade 5 pinion support bolts make our third member near-bulletproof.
Units include a Viton® pinion seal providing long lasting oil and chemical resistance. This seal retains elasticity up to 399°F (204°C) and intermittently up to 600°F (316°C) This high temp seal helps eliminate pinion leaks, reduces maintenance and keeps the third member properly lubricated. A carrier-to-housing gasket is available separately.
Our hand-assembled Ford 9 inch third member assemblies are made-to-order. We keep a supply of the most popular gears in stock, with most units built within 2-3 days. Our third-member units are shipped in a durable, reusable poly storage case, perfect for keeping multiple gear sets stored and ready for the track.
Features
Hand-assembled by our trained technicians for an unbeatable combination of quality and value
Track-tested durability in our own cars – we race what we sell
Precision assembly for the correct backlash, preload, and proper amount of pinion shims to ensure the correct pattern on the ring gear teeth
Nodular iron housing is stronger than OEM “gray” iron and has 4 lbs of additional reinforcement
Large bearing “Daytona” style pinion bearing supports for strength and reliability
Spacer and shim setup maintains critical pinion depth settings and easier to service than traditional crush sleeves
Full spools available in standard, light and mega-lite configurations
Gear units built of long-wearing 8620 cold-rolled steel, lightened gear options available
Ring gears assembled with Grade 9 hardware, 15% stronger in tensile strength than Grade 8
Viton® pinion seal, resistant to chemicals and high temperatures
Grade 8 Carrier cap bolts
Lock-style pinion nut with pre-applied Loctite®
Grade 5 pinion support bolts
Includes form fitted, reusable red poly storage case
Charts
(PDF)
Specs
Sold in Quantity
Each
Gear Material
Steel
Ring Gear Weight
Standard
Differential Type
Full Spool
Spool Weight
Standard
Yoke U-Joint Series
1310
Housing Material
Cast-Iron
Weight
77
Axle Splines
31
Gear Ratio
5.83:1
MFG. Part #
91048343-583-STD
Reviews
Yes I would buy this product again..
Rated
by Jimdandy on August 04, 2021
Summary:
i put it in my super stock race car.
Yes, I recommend this product.
Literally bolt up and go
Rated
by BJ on June 24, 2021
Summary:
Great quality, racecar runs amazing and has amazing power because of this gear!
Yes, I recommend this product.
I have bought this product again and again
Rated
by Roger on June 04, 2021
Summary:
I have used this product many times and they are great! Especially for the price
Pros:
Very knowledgeable staff
Yes, I recommend this product.
Nice
Rated
by Tom on March 31, 2021
Summary:
High quality.
Yes I would
Rated
by Furgie on December 31, 2020
Summary:
Very nice quality part
Yes, I recommend this product.
Related Items / Suggested Parts
Yoke Option for 3-1/4 Inch U-Joint with 1-1/16 Inch Caps
9 Inch Ford Rearend Axle Housing 3rd Member Pumpkin Gasket
All NEW Ford 9 Inch Third Members, Full Spool, 31-Spline
Fel-Pro P2302 9 Inch Ford Pumpkin Gaskets
Lubrication Engineers SAE 90W Gear Oil, 1 Gallon
Rear Axle Breather, AN4 Bulkhead
Shipping
Combined Shipping:
Please take advantage of the “add to cart” button on each listing to get everything in your cart prior to completing checkout. This will ensure you receive a combined shipping rate on your entire order.
Freight Shipping:
Some products are too large for standard ground delivery and must be shipped via truck freight.
Please contact us via eBay Message for a freight shipping estimate.
When possible, please provide a business or commercial address for delivery to eliminate additional fees.
Please ensure the phone number provided is accurate to avoid delays.
Upon delivery, the recipient must inspect the shipment before the driver leaves as there may be concealed damage; please open the carton to inspect the contents. Any visual damage must be noted on the shipping document BEFORE signing for delivery. Any damage not noted before signing for delivery is the buyer’s responsibility. If damage is found, the shipment may be refused, but please contact us as soon as possible and arrangements will be made to have the product replaced and damaged parts returned.
Tech Support
We’re here to help before and after your purchase. If you have a question or need assistance with one of our products, please contact us through eBay Messaging and a knowledgeable Speedway Motors team member will be happy to help.
About
Speedway Motors is America’s Oldest Speed Shop® and has been a trusted source for specialty rodding and racing products and friendly expert advice for more than 69 years. Founded in 1952 by “Speedy” Bill Smith – a racer and street rodder himself – Speedway has grown from a one-man operation to become the world’s largest manufacturer, distributor and retailer of street rod and racing products. Our industry-leading fast delivery is the result of same-day shipping from our state-of-the-art, centrally located 500,000 sq. ft. headquarters. Speedway’s size offers customers unmatched product selection and low pricing, while our excellent technical support and customer service have made us a recognized leader in the rodding and racing industries.
Return Policy
We want you to be satisfied with your purchase. If within 60 days after you receive your shipment and you are not satisfied, you may return the item for a refund. Refunds will be processed (1-2) days after the item is received by Speedway. All returned merchandise must be in original factory condition with no modifications or alterations. A restocking fee up to 15% may be applied if items are not in new condition.
Returned merchandise must include all packaging materials, warranty cards, manuals, and accessories. If the items being returned need to be repackaged, there will be a repacking charge. Repack the item in a sturdy box, include a copy of your invoice and complete the form on the back of the invoice. You must ship orders back PREPAID. WE DO NOT ACCEPT COD SHIPMENTS.
All fiberglass items returned will be subject to a 15% restocking charge. No returns on electrical parts, DVDs, and books unless they are defective. Absolutely no returns on special order or closeout merchandise.
Payment
Accepted Payment Methods – PayPal and major credit cards are accepted.
Terms – Immediate payment is required on all listings.
To view states in which sales tax will apply to your order, please visit the “shipping and payments” tab.
Guarantee
Speedway accepts full responsibility for the accuracy of our listings and product representation. If an egregious shipping or description error occurs, we are happy to assist with a replacement or refund.
Disclaimer
Due to our large inventory and the diversity of our product line, the stock photo used may not be an exact representation of the item you are bidding on. Please read all product information carefully before purchase to avoid any order issues.